/*

 * Backlight control code for Sharp Zaurus SL-5500

 *

 * Copyright 2005 John Lenz <lenz@cs.wisc.edu>

 * Maintainer: Pavel Machek <pavel@suse.cz> (unless John wants to :-)

 * GPL v2

 *

 * This driver assumes single CPU. That's okay, because collie is

 * slightly old hardware, and noone is going to retrofit second CPU to

 * old PDA.

 */

/* LCD power functions */

#include <linux/module.h>

#include <linux/init.h>

#include <linux/delay.h>

#include <linux/device.h>

#include <linux/interrupt.h>

#include <linux/fb.h>

#include <linux/backlight.h>

#include <asm/hardware/locomo.h>

#include <asm/irq.h>

#include <asm/mach/sharpsl_param.h>

#include <asm/mach-types.h>

#include "../../../arch/arm/mach-sa1100/generic.h"

static struct backlight_device *locomolcd_bl_device;

static struct locomo_dev *locomolcd_dev;

static unsigned long locomolcd_flags;

#define LOCOMOLCD_SUSPENDED     0x01

static void locomolcd_on(int comadj)

{

	locomo_gpio_set_dir(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHA_ON, 0);

	locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHA_ON, 1);

	mdelay(2);

	locomo_gpio_set_dir(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHD_ON, 0);

	locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHD_ON, 1);

	mdelay(2);

	locomo_m62332_senddata(locomolcd_dev, comadj, 0);

	mdelay(5);

	locomo_gpio_set_dir(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VEE_ON, 0);

	locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VEE_ON, 1);

	mdelay(10);

	/* TFTCRST | CPSOUT=0 | CPSEN */

	locomo_writel(0x01, locomolcd_dev->mapbase + LOCOMO_TC);

	/* Set CPSD */

	locomo_writel(6, locomolcd_dev->mapbase + LOCOMO_CPSD);

	/* TFTCRST | CPSOUT=0 | CPSEN */

	locomo_writel((0x04 | 0x01), locomolcd_dev->mapbase + LOCOMO_TC);

	mdelay(10);

	locomo_gpio_set_dir(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_MOD, 0);

	locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_MOD, 1);

}

static void locomolcd_off(int comadj)

{

	/* TFTCRST=1 | CPSOUT=1 | CPSEN = 0 */

	locomo_writel(0x06, locomolcd_dev->mapbase + LOCOMO_TC);

	mdelay(1);

	locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHA_ON, 0);

	mdelay(110);

	locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VEE_ON, 0);

	mdelay(700);

	/* TFTCRST=0 | CPSOUT=0 | CPSEN = 0 */

	locomo_writel(0, locomolcd_dev->mapbase + LOCOMO_TC);

	locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_MOD, 0);

	locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHD_ON, 0);

}

void locomolcd_power(int on)

{

	int comadj = sharpsl_param.comadj;

	unsigned long flags;

	local_irq_save(flags);

	if (!locomolcd_dev) {

		local_irq_restore(flags);

		return;

	}

	/* read comadj */

	if (comadj == -1 && machine_is_collie())

		comadj = 128;

	if (comadj == -1 && machine_is_poodle())

		comadj = 118;

	if (on)

		locomolcd_on(comadj);

	else

		locomolcd_off(comadj);

	local_irq_restore(flags);

}

EXPORT_SYMBOL(locomolcd_power);

static int current_intensity;

static int locomolcd_set_intensity(struct backlight_device *bd)

{

	int intensity = bd->props.brightness;

	if (bd->props.power != FB_BLANK_UNBLANK)

		intensity = 0;

	if (bd->props.fb_blank != FB_BLANK_UNBLANK)

		intensity = 0;

	if (locomolcd_flags & LOCOMOLCD_SUSPENDED)

		intensity = 0;

	switch (intensity) {

	/* AC and non-AC are handled differently, but produce same results in sharp code? */

	case 0: locomo_frontlight_set(locomolcd_dev, 0, 0, 161); break;

	case 1: locomo_frontlight_set(locomolcd_dev, 117, 0, 161); break;

	case 2: locomo_frontlight_set(locomolcd_dev, 163, 0, 148); break;

	case 3: locomo_frontlight_set(locomolcd_dev, 194, 0, 161); break;

	case 4: locomo_frontlight_set(locomolcd_dev, 194, 1, 161); break;

	default:

		return -ENODEV;

	}

	current_intensity = intensity;

	return 0;

}

static int locomolcd_get_intensity(struct backlight_device *bd)

{

	return current_intensity;

}

static struct backlight_ops locomobl_data = {

	.get_brightness = locomolcd_get_intensity,

	.update_status  = locomolcd_set_intensity,

};

#ifdef CONFIG_PM

static int locomolcd_suspend(struct locomo_dev *dev, pm_message_t state)

{

	locomolcd_flags |= LOCOMOLCD_SUSPENDED;

	locomolcd_set_intensity(locomolcd_bl_device);

	return 0;

}

static int locomolcd_resume(struct locomo_dev *dev)

{

	locomolcd_flags &= ~LOCOMOLCD_SUSPENDED;

	locomolcd_set_intensity(locomolcd_bl_device);

	return 0;

}

#else

#define locomolcd_suspend	NULL

#define locomolcd_resume	NULL

#endif

static int locomolcd_probe(struct locomo_dev *ldev)

{

	unsigned long flags;

	local_irq_save(flags);

	locomolcd_dev = ldev;

	locomo_gpio_set_dir(ldev->dev.parent, LOCOMO_GPIO_FL_VR, 0);

	/* the poodle_lcd_power function is called for the first time

	 * from fs_initcall, which is before locomo is activated.

	 * We need to recall poodle_lcd_power here*/

	if (machine_is_poodle())

		locomolcd_power(1);

	local_irq_restore(flags);

	locomolcd_bl_device = backlight_device_register("locomo-bl", &ldev->dev, NULL, &locomobl_data);

	if (IS_ERR (locomolcd_bl_device))

		return PTR_ERR (locomolcd_bl_device);

	/* Set up frontlight so that screen is readable */

	locomolcd_bl_device->props.max_brightness = 4,

	locomolcd_bl_device->props.brightness = 2;

	locomolcd_set_intensity(locomolcd_bl_device);

	return 0;

}

static int locomolcd_remove(struct locomo_dev *dev)

{

	unsigned long flags;

	locomolcd_bl_device->props.brightness = 0;

	locomolcd_bl_device->props.power = 0;

	locomolcd_set_intensity(locomolcd_bl_device);

	backlight_device_unregister(locomolcd_bl_device);

	local_irq_save(flags);

	locomolcd_dev = NULL;

	local_irq_restore(flags);

	return 0;

}

static struct locomo_driver poodle_lcd_driver = {

	.drv = {

		.name = "locomo-backlight",

	},

	.devid	= LOCOMO_DEVID_BACKLIGHT,

	.probe	= locomolcd_probe,

	.remove	= locomolcd_remove,

	.suspend = locomolcd_suspend,

	.resume = locomolcd_resume,

};

static int __init locomolcd_init(void)

{

	int ret = locomo_driver_register(&poodle_lcd_driver);

	if (ret)

		return ret;

#ifdef CONFIG_SA1100_COLLIE

	sa1100fb_lcd_power = locomolcd_power;

#endif

	return 0;

}

static void __exit locomolcd_exit(void)

{

	locomo_driver_unregister(&poodle_lcd_driver);

}

module_init(locomolcd_init);

module_exit(locomolcd_exit);

MODULE_AUTHOR("John Lenz <lenz@cs.wisc.edu>, Pavel Machek <pavel@suse.cz>");

MODULE_DESCRIPTION("Collie LCD driver");

MODULE_LICENSE("GPL");