sd-card: Only add header to the results file if it’s empty
[brewing-logger:firmware.git] / main.c
2012-12-09 Philip Withnallmain: Take a set of sensor readings before enabling...
2012-12-09 Philip Withnallmain: Remove some unnecessary zero padding from output...
2012-12-09 Philip Withnallspi: Split SPI bus state from SPI chip selects
2012-12-09 Philip Withnallpower: Split sensor power management code out into...
2012-12-08 Philip Withnallmain: Disable various MCU components to save power
2012-12-08 Philip Withnallflash-rom: Add support for DP and RES instructions...
2012-12-08 Philip Withnallmain: Add support for gating power to the sensors
2012-12-08 Philip Withnalllcd: Add support for gating power to the LCD
2012-12-08 Philip Withnallsleep: Fix various bugs with the event handling/sleep...
2012-12-06 Philip Withnallcode: Display a UI message about heater failure if...
2012-12-06 Philip Withnallcode: Implement the heater controller and safety mechanisms
2012-12-05 Philip Withnallcode: Move the sleep/watchdog code out into a separate...
2012-12-05 Philip Withnallcode: Disable static assertions if the compiler doesn...
2012-12-03 Philip Withnallcode: Tidy up assertions and non-nulls
2012-12-03 Philip Withnallcode: Implement the main UI
2012-12-02 Philip Withnallcode: Add support for a UI input button
2012-12-02 Philip Withnallcode: Fix whitespace in main.c
2012-12-02 Philip Withnallcode: Tidy up a function call
2012-12-02 Philip Withnallcode: Change units for gas concentration measurements
2012-12-01 Philip Withnallcode: Improve error handling when taking sensor measure...
2012-12-01 Philip Withnallcode: Ensure the Flash ROM is initialised during boot
2012-11-28 Philip Withnallcode: Implement periodic flushing of the Flash ROM...
2012-11-28 Philip Withnallcode: Initialise the sensors in main()
2012-11-28 Philip Withnallcode: Change units for temperature
2012-11-28 Philip Withnallcode: Handle checksum failures on boot
2012-11-27 Philip Withnallcode: Fix various compiler warnings
2012-11-27 Philip Withnallcode: Add a checksum to the BrewConfig structure
2012-11-27 Philip Withnallcode: Add a brew ID to each LogEntry
2012-11-27 Philip Withnallcode: Clarify semantics of BrewConfig.fermentation_temp...
2012-11-27 Philip Withnallcode: Remove padding from BrewConfig structure
2012-11-27 Philip Withnallcode: Refactor ADC handling code into adc.[ch] and...
2012-11-23 Philip Withnallcode: Add a self-test mode which is enabled by a compil...
2012-11-23 Philip Withnallcode: Move LCD initialisation code out into separate...
2012-11-23 Philip Withnallcode: Fix watchdog timer to not be in System Reset...
2012-11-23 Philip Withnallcode: Refactor initialisation in main.c a little
2012-11-23 Philip Withnallcode: Initialise the SD card when booting
2012-11-23 Philip Withnallcode: Tidy up message printing in main.c
2012-11-23 Philip Withnallcode: Fix initialisation of the SPI bus
2012-11-21 Philip Withnallcode: Add code to read the RHT03 humidity/temperature...
2012-11-21 Philip Withnallcode: Create a default brew config file if one isn...
2012-11-20 Philip Withnallcode: Tidy up initialisation error output a little
2012-11-16 Philip Withnallcode: Fix a number of compiler warnings and errors
2012-11-14 Philip Withnallcode: Implement the bulk of the main loop of the program
2012-11-14 Philip Withnallmeta: Move TODO list to a separate file
2012-11-09 Philip Withnallcode: Add skeleton of the code for the project