brewing-logger:firmware.git
2012-12-09 Philip Withnallsd-card: Only add header to the results file if it...
2012-12-09 Philip Withnallmain: Take a set of sensor readings before enabling...
2012-12-09 Philip Withnallmain: Remove some unnecessary zero padding from output...
2012-12-09 Philip Withnalllcd: Take the LCD data line low when powering down...
2012-12-09 Philip Withnallflash-rom, sd-card: Add comments about endianness in...
2012-12-09 Philip Withnallbuild: Add -ggdb flag to CFLAGS for firmware and simulator
2012-12-09 Philip Withnallsd-card: Add a header and checksums to the brew results...
2012-12-09 Philip Withnallbuild: Update .gitignore file
2012-12-09 Philip Withnallsimulation: Add conditional support for VCDs of SPI...
2012-12-09 Philip Withnallspi: Split SPI bus state from SPI chip selects
2012-12-09 Philip Withnallsd-card: Document the flushing behaviour of appending...
2012-12-09 Philip Withnallsd-card: Remove call to disk_initialize()
2012-12-09 Philip Withnallhumidity: Make humidity measurement initialisation...
2012-12-09 Philip Withnalllcd: Add a delay after enabling the LCD power domain
2012-12-09 Philip Withnallconfig: Remove some outdated TODOs
2012-12-09 Philip Withnallpower: Split sensor power management code out into...
2012-12-08 Philip Withnallhumidity: Disable interrupts while in the humidity...
2012-12-08 Philip Withnallmeta: Add bug about adding power-down support to the...
2012-12-08 Philip Withnallmain: Disable various MCU components to save power
2012-12-08 Philip Withnallflash-rom: Add support for DP and RES instructions...
2012-12-08 Philip Withnallrtc: Disable a few RTC features on initialisation
2012-12-08 Philip Withnallheater: Fix controller to use signed fixed point rather...
2012-12-08 Philip Withnallmain: Add support for gating power to the sensors
2012-12-08 Philip Withnalllcd: Add support for gating power to the LCD
2012-12-08 Philip Withnallsleep: Fix various bugs with the event handling/sleep...
2012-12-08 Philip Withnallgas: Add support for turning the gas sensor’s heater...
2012-12-07 Philip Withnallmeta: Mark some hardware bugs as fixed
2012-12-07 Philip Withnallhumidity: Un-inline functions
2012-12-06 Philip Withnallbuild: Fix reference to non-existent common Makefile
2012-12-06 Philip Withnallcode: Add lots of missing documentation
2012-12-06 Philip Withnallcode: Fix SPI pin configuration
2012-12-06 Philip Withnallcode: Add a test for the heater code
2012-12-06 Philip Withnallcode: Display a UI message about heater failure if...
2012-12-06 Philip Withnallcode: Implement the heater controller and safety mechanisms
2012-12-06 Philip Withnallmeta: Add some new bugs
2012-12-05 Philip Withnallcode: Add a Flash ROM test
2012-12-05 Philip Withnallcode: Refactor Flash ROM code a lot
2012-12-05 Philip Withnallcode: Add a test for the UI button
2012-12-05 Philip Withnallcode: Move the sleep/watchdog code out into a separate...
2012-12-05 Philip Withnallcode: Disable static assertions if the compiler doesn...
2012-12-05 Philip Withnallcode: Fix comments in diskio licencing headers
2012-12-04 Philip Withnallcode: Fix seeking to the end of the results file in...
2012-12-03 Philip Withnallcode: Fix handling of unusual return values in SD card...
2012-12-03 Philip Withnallcode: Fix f_open() flags used in the SD card code
2012-12-03 Philip Withnallsimulation: Ensure the M25P is initialised to all 1s
2012-12-03 Philip Withnallsimulation: Fix address handling in the M25P simulation
2012-12-03 Philip Withnallcode: Various fixes to the Flash ROM code as a result...
2012-12-03 Philip Withnallmeta: Add a COPYING file to make the licencing more...
2012-12-03 Philip Withnallcode: Clarify licencing of code in the ‘lib’ directory
2012-12-03 Philip Withnallcode: Tidy up assertions and non-nulls
2012-12-03 Philip Withnallsimulation: Remove lingering debug output from the...
2012-12-03 Philip Withnallcode: Implement the main UI
2012-12-03 Philip Withnallcode: Fix some signed/unsigned comparisons in the gas...
2012-12-03 Philip Withnallcode: Fix gas sensor interpolation code after some...
2012-12-03 Philip Withnallmeta: Mark two hardware bugs as fixed
2012-12-02 Philip Withnallcode: Fix conversion of temperature readings
2012-12-02 Philip Withnallcode: Fix krausen level code to correctly give results...
2012-12-02 Philip Withnallcode: Eliminate floating point from the ADC code
2012-12-02 Philip Withnallcode: Add a test for the gas concentration sensor
2012-12-02 Philip Withnallcode: Add support for a UI input button
2012-12-02 Philip Withnallcode: Fix whitespace in main.c
2012-12-02 Philip Withnallcode: Tidy up a function call
2012-12-02 Philip Withnallcode: Change units for gas concentration measurements
2012-12-01 Philip Withnallcode: Improve error handling when taking sensor measure...
2012-12-01 Philip Withnallmeta: Move TODO list to Bugs Everywhere
2012-12-01 Philip Withnallsimulation: Add a simulated Flash ROM peripheral
2012-12-01 Philip Withnallsimulation: Remove some unnecessary debug spew from...
2012-12-01 Philip Withnallcode: Ensure the Flash ROM is initialised during boot
2012-12-01 Philip Withnallcode: Add support for SPI chip selection
2012-11-30 Philip Withnallcode: Rename some enum values in the Flash ROM
2012-11-30 Philip Withnallsimulation: Fix chip select pin connection for SD card...
2012-11-30 Philip Withnallsimulation: Disable debugging in the simulated SD card
2012-11-30 Philip Withnallmeta: Add bug tracking using Bugs Everywhere
2012-11-30 Philip Withnallsimulation: Add a SIGINT signal handler to exit the...
2012-11-30 Philip Withnallcode: Use an SFD partition table rather than an FDISK one
2012-11-30 Philip Withnallsimulation: Add a simulated SD card peripheral
2012-11-29 Philip Withnallsimulation: Ensure serial LCD output is flushed regularly
2012-11-29 Philip Withnallsimulation: Add a simulated RHT03 peripheral
2012-11-29 Philip Withnallsimulation: Add a simulated DS3231 RTC peripheral
2012-11-28 Philip Withnallbuild: Improve ‘simulate’ target in the Makefile
2012-11-28 Philip Withnallsimulation: Allow the gdb port to be specified on the...
2012-11-28 Philip Withnallcode: Explicitly set the default states on the LCD...
2012-11-28 Philip Withnallsimulation: Add a simulated serial LCD peripheral
2012-11-28 Philip Withnallsimulation: Add the beginnings of a simavr-based simula...
2012-11-28 Philip Withnallcode: Fix the defined reference voltage for the MCU
2012-11-28 Philip Withnallcode: Implement periodic flushing of the Flash ROM...
2012-11-28 Philip Withnallcode: Initialise the sensors in main()
2012-11-28 Philip Withnallcode: Fix tests which use the ADC
2012-11-28 Philip Withnallbuild: Remove a compiler flag which isn’t supported...
2012-11-28 Philip Withnallcode: Change units for humidity measurements
2012-11-28 Philip Withnallcode: Change units for krausen level
2012-11-28 Philip Withnallcode: Change units for temperature
2012-11-28 Philip Withnallcode: Add measurement code for the krausen level using...
2012-11-28 Philip Withnallcode: Fix various compiler warnings in the library...
2012-11-28 Philip Withnallcode: Handle checksum failures on boot
2012-11-27 Philip Withnallcode: Fix various compiler warnings
2012-11-27 Philip Withnallcode: Add some documentation comments
2012-11-27 Philip Withnallbuild: Enable a load of extra compiler warnings
2012-11-27 Philip Withnallcode: Tidy up handling of response enums in sd-card...
2012-11-27 Philip Withnallbuild: Add simulation support using simavr
next