nm-kernel:u-boot-nm.git
4 years agoPrepare v2013.10-rc2 v2013.10-rc2
Tom Rini [Mon, 2 Sep 2013 18:20:36 +0000 (14:20 -0400)]
Prepare v2013.10-rc2

Signed-off-by: Tom Rini <trini@ti.com>
4 years agoomap5: Correct include order, drop CONFIG_SYS_PROMPT define
Tom Rini [Tue, 27 Aug 2013 14:56:18 +0000 (10:56 -0400)]
omap5: Correct include order, drop CONFIG_SYS_PROMPT define

With the new include structure for TI platforms, we need to not define
our own CONFIG_SYS_PROMPT and also need to include
<configs/omap5_common.h> much sooner, so do both of these.  Also drop
the unused CONFIG_NET_MULTI

Signed-off-by: Tom Rini <trini@ti.com>
4 years agoMerge branch 'master' of git://git.denx.de/u-boot-usb
Tom Rini [Tue, 27 Aug 2013 13:49:43 +0000 (09:49 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb

4 years agoi2c: fix i2c dev command for not using new framework
Heiko Schocher [Fri, 23 Aug 2013 07:39:16 +0000 (09:39 +0200)]
i2c: fix i2c dev command for not using new framework

i2c dev command does not work anymore for legacy drivers
because a check is executed that is valid only
in the new framework.

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
4 years agoconsole: usb: kbd: To fix slow TFTP booting
Jim Lin [Mon, 26 Aug 2013 12:21:09 +0000 (20:21 +0800)]
console: usb: kbd: To fix slow TFTP booting

TFTP booting is slow when a USB keyboard is installed and
stdin has usbkbd added.
This fix is to change Ctrl-C polling for USB keyboard to every second
when NET transfer is running.
My previous patch is expected to be put into usb_kbd_testc(). But it went
into usb_kbd_getc() after applied.
This patch is to put change in correct place.

Signed-off-by: Jim Lin <jilin@nvidia.com>
4 years agoconsole: usb: kbd: To improve TFTP booting performance
Jim Lin [Tue, 13 Aug 2013 11:04:22 +0000 (19:04 +0800)]
console: usb: kbd: To improve TFTP booting performance

TFTP booting is slow when a USB keyboard is installed and
stdin has usbkbd added.
This fix is to change Ctrl-C polling for USB keyboard to every second
when NET transfer is running.

Signed-off-by: Jim Lin <jilin@nvidia.com>
4 years agoNET: Add net_busy_flag if CONFIG_USB_KEYBOARD is defined
Jim Lin [Tue, 13 Aug 2013 11:03:05 +0000 (19:03 +0800)]
NET: Add net_busy_flag if CONFIG_USB_KEYBOARD is defined

This flag is to make console aware that NET transfer is running or not.

Signed-off-by: Jim Lin <jilin@nvidia.com>
4 years agousb: ehci-mx5: Use 'bool' instead of 'unsigned char'
Fabio Estevam [Fri, 26 Jul 2013 16:54:28 +0000 (13:54 -0300)]
usb: ehci-mx5: Use 'bool' instead of 'unsigned char'

The 'enable' argument can be better expressed as boolean.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
4 years agousb: ehci-mx5: Remove unneeded write to cscmr1 register
Fabio Estevam [Fri, 26 Jul 2013 16:54:27 +0000 (13:54 -0300)]
usb: ehci-mx5: Remove unneeded write to cscmr1 register

Currently we have the following behavior in ehci_hcd_init()

- Read csmr1 register, clear bit 26 and then set bit 26.

However a little bit later we call set_usb_phy_clk() which clears bit 26, so
let's get rid of the unnecessary code.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
4 years agousb:dfu:g_dnl: Refactoring the string definition code for g_dnl driver
Lukasz Majewski [Mon, 19 Aug 2013 15:17:19 +0000 (17:17 +0200)]
usb:dfu:g_dnl: Refactoring the string definition code for g_dnl driver

The manufacturer and product IDs are dynamically assigned when gadget is
bind.
Now the IDs aren't assigned at struct g_dnl_string_defs definition.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
4 years agousb:dfu:g_dnl: Change number of exported configurations at composite gadget
Lukasz Majewski [Mon, 19 Aug 2013 15:17:18 +0000 (17:17 +0200)]
usb:dfu:g_dnl: Change number of exported configurations at composite gadget

USB composite gadget (g_dnl) supports only one configuration. Due to that
the corresponding field - bConfigurationValue has been changed.

Moreover more descriptive names were chosen for relevant fields.

Windows XP setup:
- Thesyscon USB Descriptor Dumper
- zadig_xp program for WinUSB installation (which is required by dfu-util)
- dfu-util for windows (version 0.6)
- TRATS target connected via USB hub to test Win XP machine.

Tested at: Trats - Exynos4210

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
4 years agodfu, nand, ubi: add partubi alt settings for updating ubi partition
Heiko Schocher [Thu, 25 Jul 2013 04:43:11 +0000 (06:43 +0200)]
dfu, nand, ubi: add partubi alt settings for updating ubi partition

updating an ubi partition needs a completely erased mtd partition,
see:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html

So, add partubi alt setting for the dfu_alt_info environment
variable to mark this partition as an ubi partition. In case we
update an ubi partition, we erase after flashing the image into the
partition, the remaining sektors.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
4 years agousb: Use well-known descriptor sizes when parsing configuration
Julius Werner [Fri, 19 Jul 2013 20:12:08 +0000 (13:12 -0700)]
usb: Use well-known descriptor sizes when parsing configuration

The existing USB configuration parsing code relies on the descriptors'
own length values when reading through the configuration blob. Since the
size of those descriptors is always well-defined, we should rather use
the known sizes instead of trusting device-provided values to be
correct. Also adds some safety to potential out-of-order descriptors.

Change-Id: I16f69dfdd6793aa0fe930b5148d4521f3e5c3090
Signed-off-by: Julius Werner <jwerner@chromium.org>
4 years agoARM: OMAP5-uevm: Add usb device reset API
Dan Murphy [Thu, 1 Aug 2013 19:06:02 +0000 (14:06 -0500)]
ARM: OMAP5-uevm: Add usb device reset API

Add the call back to reset the LAN9730 after
the FEAT_POWER has been called.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
4 years agoUSB: usb-hub: Add a weak function for resetting devices
Dan Murphy [Thu, 1 Aug 2013 19:06:01 +0000 (14:06 -0500)]
USB: usb-hub: Add a weak function for resetting devices

Add a __weak function that can be overridden to reset devices
attached to an ehci devices after the FEAT_POWER has been submitted

Signed-off-by: Dan Murphy <dmurphy@ti.com>
4 years agoARM: OMAP5-uevm: Add USB MAC ethernet address
Dan Murphy [Thu, 1 Aug 2013 19:06:00 +0000 (14:06 -0500)]
ARM: OMAP5-uevm: Add USB MAC ethernet address

Set the usbethaddr based on the OMAP DIE_ID registers
which should be unique for each processor.

Then set this as the usb ethernet MAC address.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
4 years agoARM: OMAP5-uevm: Add USB ehci support for the uEVM
Dan Murphy [Thu, 1 Aug 2013 19:05:59 +0000 (14:05 -0500)]
ARM: OMAP5-uevm: Add USB ehci support for the uEVM

Add the USB ehci support for the OMAP5 uEVM.

Configure the uEVM mux data
Add the flags to build the appropriate modules
Add the usb call backs to initialize the EHCI controller

Signed-off-by: Dan Murphy <dmurphy@ti.com>
4 years agoARM: OMAP: USB: Fix linker error when ULPI is not defined
Dan Murphy [Thu, 1 Aug 2013 19:05:58 +0000 (14:05 -0500)]
ARM: OMAP: USB: Fix linker error when ULPI is not defined

Fix the linker error for missing ulpi_reset when ulpi is not defined
in the board config.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
4 years agoARM: OMAP5: USB: Add OMAP5 common USB EHCI information
Dan Murphy [Thu, 1 Aug 2013 19:05:57 +0000 (14:05 -0500)]
ARM: OMAP5: USB: Add OMAP5 common USB EHCI information

* Enable the OMAP5 EHCI host clocks
* Add OMAP5 EHCI register definitions
* Add OMAP5 ES2 host revision

Signed-off-by: Dan Murphy <dmurphy@ti.com>
4 years agoomap5: uevm: Change the board name to correct name
Dan Murphy [Thu, 1 Aug 2013 19:05:56 +0000 (14:05 -0500)]
omap5: uevm: Change the board name to correct name

Change the board name for the sys info to
5432 uEVM

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
4 years agoenv_nand.c: support falling back to redundant env when writing
Phil Sutter [Fri, 19 Jul 2013 10:20:26 +0000 (12:20 +0200)]
env_nand.c: support falling back to redundant env when writing

Without this patch, when the currently chosen environment to be written
has bad blocks, saveenv fails completely. Instead, when there is
redundant environment fall back to the other copy. Environment reading
needs no adjustment, as the fallback logic for incomplete writes applies
to this case as well.

Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
4 years agonand_util: delete a useless variable
Masahiro Yamada [Fri, 12 Jul 2013 01:53:37 +0000 (10:53 +0900)]
nand_util: delete a useless variable

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
4 years agocmd_nand: Do not show usage when scrub is aborted
Masahiro Yamada [Thu, 11 Jul 2013 08:29:57 +0000 (17:29 +0900)]
cmd_nand: Do not show usage when scrub is aborted

When executing nand scrub, the user gets the prompt:

  Really scrub this NAND flash? <y/N>

We do not want the annoying usage displayed when saying N here.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
4 years agocmd_nand: slight optimization of nand_dump function
Masahiro Yamada [Thu, 11 Jul 2013 08:27:13 +0000 (17:27 +0900)]
cmd_nand: slight optimization of nand_dump function

If a non-zero value is given to only_oob argument,
printing the main area is skipped.

With a little modification, we can skip the whole
while loop.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
4 years agocmd_nand: fix a memory leak in nand_dump function
Masahiro Yamada [Thu, 11 Jul 2013 08:27:12 +0000 (17:27 +0900)]
cmd_nand: fix a memory leak in nand_dump function

If datbuf = memalign(ARCH_DMA_MINALIGN, nand->writesize);
succeeds and
  oobbuf = memalign(ARCH_DMA_MINALIGN, nand->oobsize);
fails, nand_dump function should free databuf.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
4 years agoMerge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Tom Rini [Wed, 21 Aug 2013 20:27:47 +0000 (16:27 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

4 years agoMakefile: Fix build in a separated directory tree
York Sun [Wed, 21 Aug 2013 16:03:29 +0000 (09:03 -0700)]
Makefile: Fix build in a separated directory tree

Fix a bug introduced by commit 3aa29dee
TPL : introduce the TPL based on the SPL

Signed-off-by: York Sun <yorksun@freescale.com>
4 years agoFix for incorrect conversion hex string to number (FMAN firmware address).
Николай Пузанов [Wed, 19 Jun 2013 07:48:44 +0000 (11:48 +0400)]
Fix for incorrect conversion hex string to number (FMAN firmware address).

Signed-off-by: Николай Пузанов <punzik@gmail.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc/sec: Add workaround for SEC A-003571
Shengzhou Liu [Thu, 15 Aug 2013 01:31:47 +0000 (09:31 +0800)]
powerpc/sec: Add workaround for SEC A-003571

Multiple read/write transactions initiated by security
engine may cause system to hang.
Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc/p1010rdb: fix calculating ddr_freq_mhz
Shengzhou Liu [Tue, 13 Aug 2013 08:41:19 +0000 (16:41 +0800)]
powerpc/p1010rdb: fix calculating ddr_freq_mhz

There was a bug for calculating ddr_freq_mhz,
it should be divided by 1000000 rather than 0x1000000.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc/t4240: add QSGMII interface support
Shaohui Xie [Mon, 19 Aug 2013 10:58:52 +0000 (18:58 +0800)]
powerpc/t4240: add QSGMII interface support

Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc/t4240: fix lanes routing for QSGMII protocols
Shaohui Xie [Mon, 19 Aug 2013 10:57:57 +0000 (18:57 +0800)]
powerpc/t4240: fix lanes routing for QSGMII protocols

When using QSGMII protocols, the first lane and third lane on each slot
need to be swapped.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc/common/vsc3316: remove const from vsc3316_config parameter define
Shaohui Xie [Mon, 19 Aug 2013 10:43:07 +0000 (18:43 +0800)]
powerpc/common/vsc3316: remove const from vsc3316_config parameter define

Since the parameters need to be modified according to different Serdes
protocols at runtime, the const will block this. Also remove const from
arrays define used by vsc3316_config.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpcv2: Print hardcoded size like print_size() does
Shruti Kanetkar [Thu, 15 Aug 2013 16:25:38 +0000 (11:25 -0500)]
powerpcv2: Print hardcoded size like print_size() does

Makes the startup output more consistent

Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc: Use print_size() where appropriate
Shruti Kanetkar [Thu, 15 Aug 2013 16:25:37 +0000 (11:25 -0500)]
powerpc: Use print_size() where appropriate

Makes the startup output more consistent

Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agoSPDX-License-Identifier: clean up license header
York Sun [Tue, 20 Aug 2013 17:15:37 +0000 (10:15 -0700)]
SPDX-License-Identifier: clean up license header

This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c

Signed-off-by: York Sun <yorksun@freescale.com>
4 years agopowerpc: Fix CamelCase checkpatch warnings
Prabhakar Kushwaha [Fri, 16 Aug 2013 09:22:26 +0000 (14:52 +0530)]
powerpc: Fix CamelCase checkpatch warnings

85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".

Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc: p1022ds: add TPL for p1022ds nand boot
Ying Zhang [Fri, 16 Aug 2013 07:16:16 +0000 (15:16 +0800)]
powerpc: p1022ds: add TPL for p1022ds nand boot

TPL is introduced in the patch "NAND: TPL : introduce the TPL
based on the SPL", here enable TPL for p1022ds nand boot.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agoTPL : introduce the TPL based on the SPL
Ying Zhang [Fri, 16 Aug 2013 07:16:15 +0000 (15:16 +0800)]
TPL : introduce the TPL based on the SPL

Due to the nand SPL on some board(e.g. P1022DS)has a size limit, it can
not be more than 4K. So, the SPL cannot initialize the DDR with the SPD
code. This patch introduces TPL to enable a loader stub that is loaded
by the code from the SPL. It initializes the DDR with the SPD or other
operations.

The TPL's size is sizeable, the maximum size is decided by the memory's
size that TPL runs. It initializes the DDR through SPD code, and copys
final uboot image to DDR. So there are three stage uboot images:
* spl_boot, * tpl_boot, * final uboot image

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc : p1022ds : Enable p1022ds to start from eSPI with SPL
Ying Zhang [Fri, 16 Aug 2013 07:16:14 +0000 (15:16 +0800)]
powerpc : p1022ds : Enable p1022ds to start from eSPI with SPL

Enable p1022ds to start from eSPI with SPL.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc : spi flash : Support to start from eSPI with SPL
Ying Zhang [Fri, 16 Aug 2013 07:16:13 +0000 (15:16 +0800)]
powerpc : spi flash : Support to start from eSPI with SPL

This patch introduces SPL to enable a loader stub that being loaded by
the code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.

The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc: p1022ds: Enable P1022DS to boot from SD Card with SPL
Ying Zhang [Fri, 16 Aug 2013 07:16:12 +0000 (15:16 +0800)]
powerpc: p1022ds: Enable P1022DS to boot from SD Card with SPL

Enable p1022ds to start from eSDHC with SPL.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc: mpc85xx: Support booting from SD Card with SPL
Ying Zhang [Fri, 16 Aug 2013 07:16:11 +0000 (15:16 +0800)]
powerpc: mpc85xx: Support booting from SD Card with SPL

The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.

The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agopowerpc: deleted unused symbol CONFIG_SPL_NAND_MINIMAL and enabled some functionality...
Ying Zhang [Fri, 16 Aug 2013 07:16:10 +0000 (15:16 +0800)]
powerpc: deleted unused symbol CONFIG_SPL_NAND_MINIMAL and enabled some functionality for common SPL

1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it.
2. Some functions were unused in the minimal SPL, but it is useful
in the common SPL. So, enabled some functionality for common SPL.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agospl: env_common.c: make CONFIG_SPL_BUILD contain function env_import
Ying Zhang [Thu, 20 Jun 2013 08:04:24 +0000 (16:04 +0800)]
spl: env_common.c: make CONFIG_SPL_BUILD contain function env_import

The functionality env_import will be used in the SPL. They
had been excluded by ifndef CONFIG_SPL_BUILD. Now, put it
into the SPL.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agoppc4xx: Remove support for PPC405CR CPUs
Matthias Fuchs [Wed, 7 Aug 2013 10:10:38 +0000 (12:10 +0200)]
ppc4xx: Remove support for PPC405CR CPUs

This patch removes support for the APM 405CR CPU.
This CPU is EOL and no board uses this chip.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
4 years agoppc4xx: Remove CANBT board
Matthias Fuchs [Wed, 7 Aug 2013 11:22:10 +0000 (13:22 +0200)]
ppc4xx: Remove CANBT board

This board and especially the CPU (PPC405CR) is EOL.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Wolfgang Denk <wd@denx.de>
4 years agoMerge branch 'master' of git://git.denx.de/u-boot-i2c
Tom Rini [Tue, 20 Aug 2013 15:34:24 +0000 (11:34 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c

4 years agopmic:i2c: Replace legacy I2C_SET_BUS macro with i2c_set_bus_num()
Łukasz Majewski [Fri, 16 Aug 2013 13:35:26 +0000 (15:35 +0200)]
pmic:i2c: Replace legacy I2C_SET_BUS macro with i2c_set_bus_num()

After introduction of unified i2c model, the I2C_SET_BUS() macro is regarded
as obsolete.
Hence it is replaced with i2c_set_bus_num() function call.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
4 years agoi2c:samsung: Adjust Trats, GONI and Universal_c210 boards to work with new I2C framework
Łukasz Majewski [Fri, 16 Aug 2013 13:33:33 +0000 (15:33 +0200)]
i2c:samsung: Adjust Trats, GONI and Universal_c210 boards to work with new I2C framework

New I2C framework, introduced after v2013.07 final release, imposed I2C
code adjustment for some Samsung boards - namely Trats, GONI and Universal_c210.

Those boards were using schematic based I2C enumeration (I2C_5, I2C_9).
However, new I2C framework imposes usage of logical I2C adapters numbering
(e.g. I2C_0, I2C_1, etc).

Additionally, I2C_GET_* macros were replaced with i2c_*_bus_num() functions.

Trats board gained definition of second soft I2C adapter.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
4 years agoi2c:multibus:fix: Correct I2C_MULTI_BUS value when support for many buses is enabled
Łukasz Majewski [Fri, 16 Aug 2013 13:31:45 +0000 (15:31 +0200)]
i2c:multibus:fix: Correct I2C_MULTI_BUS value when support for many buses is enabled

The I2C_MULTI_BUS needs to be defined for correct I2C operation with
many software emulated I2C controllers.

This fix restores correct value of the I2C_MULTI_BUS changed by following
commit:

SHA1: 385c9ef5a7215b2b0c22836fee6c692dfc8559d7
i2c: add i2c_core and prepare for new multibus support

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
4 years agofsl_i2c: add workaround for the erratum I2C A004447
Chunhe Lan [Fri, 16 Aug 2013 07:10:37 +0000 (15:10 +0800)]
fsl_i2c: add workaround for the erratum I2C A004447

This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.

At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.

The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
4 years agofsl_i2c: generate nine pulses on SCL if the I2C bus is hung
Chunhe Lan [Fri, 16 Aug 2013 07:10:36 +0000 (15:10 +0800)]
fsl_i2c: generate nine pulses on SCL if the I2C bus is hung

When the code detected that the bus is hung (e.g. SDA stuck low),
send 9 pulses on SCL to try to fixup the bus.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
4 years agoSPL: Makefile: Build a separate autoconf.mk for SPL
Joel Fernandes [Mon, 19 Aug 2013 08:14:14 +0000 (16:14 +0800)]
SPL: Makefile: Build a separate autoconf.mk for SPL

SPL defines CONFIG_SPL_BUILD but this does not percolate to the
autoconf.mk Makefile.  As a result the build breaks when
CONFIG_SPL_BUILD is used in the board-specific include header file. With
this, there is a possibility of having a CONFIG option defined in the
header file but not defined in the Makefile causing all kinds of build
failure and problems.

It also messes things for up, for example, when one might want to
undefine options to keep the SPL small and doesn't want to be stuck with
the CONFIG options used for U-boot.  Lastly, this also avoids defining
special CONFIG_SPL_ variables for cases where some options are required
in U-boot but not in SPL.

We add a spl-autoconf.mk rule that is generated for SPL with the
CONFIG_SPL_BUILD flag and conditionally include it for SPL builds.

Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Ying Zhang <b40530@freescale.com>
4 years agoPrepare v2013.10-rc1 v2013.10-rc1
Tom Rini [Mon, 19 Aug 2013 21:26:15 +0000 (17:26 -0400)]
Prepare v2013.10-rc1

Signed-off-by: Tom Rini <trini@ti.com>
4 years agoSPDX-License-Identifier: convert BSD-3-Clause files
Wolfgang Denk [Sun, 28 Jul 2013 20:12:47 +0000 (22:12 +0200)]
SPDX-License-Identifier: convert BSD-3-Clause files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini Don't remove some copyrights by accident]
Signed-off-by: Tom Rini <trini@ti.com>
4 years agoboard/esd/cpci750/mv_eth.c: Fix license
Wolfgang Denk [Sun, 28 Jul 2013 20:12:46 +0000 (22:12 +0200)]
board/esd/cpci750/mv_eth.c: Fix license

The file header indicated that this file was GPL-2.0+, but actually
the code was derived from (Marvell based) Linux source code which is
only GPL-2.0.  Fix this.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
4 years agoSPDX-License-Identifier: convert PIBS licensed files
Wolfgang Denk [Sun, 28 Jul 2013 20:12:45 +0000 (22:12 +0200)]
SPDX-License-Identifier: convert PIBS licensed files

This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.

So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.

Note that the following files contained incorrect license information:

arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h

These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect.  This has been removed.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
4 years agoSPDX-License-Identifier: fixing some problematic GPL-2.0 files
Wolfgang Denk [Sun, 28 Jul 2013 20:12:44 +0000 (22:12 +0200)]
SPDX-License-Identifier: fixing some problematic GPL-2.0 files

Unlike the other patches in this series so far, this commit fixes a
ambiguity in the license terms for some OMAP files:  the code was
originally derived from the Linux kernel sources, where it was clearly
marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot
version had a GPL-2.0+ file header added, apparently without
permission / relicensing from the original authors of the code.

Insert a GPL-2.0 SPDX-License-Identifier to fix this.

Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
4 years agoSPDX-License-Identifier: convert GPL-2.0+ / BSD-2-Clause dual-licensed files
Wolfgang Denk [Sun, 28 Jul 2013 20:12:43 +0000 (22:12 +0200)]
SPDX-License-Identifier: convert GPL-2.0+ / BSD-2-Clause dual-licensed files

Signed-off-by: Wolfgang Denk <wd@denx.de>
4 years agonet: ftmac110: Update tx/rx descriptor format
Kuo-Jung Su [Wed, 10 Jul 2013 01:25:49 +0000 (09:25 +0800)]
net: ftmac110: Update tx/rx descriptor format

1. Reformat tx/rx descriptor as an uniform struct.
2. Replace uint32_t[2] with uint64_t for descriptor control.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
4 years agonet: ftmac110: struct ftmac110_regs __iomem * -> struct ftmac110_regs *
Kuo-Jung Su [Wed, 10 Jul 2013 01:25:48 +0000 (09:25 +0800)]
net: ftmac110: struct ftmac110_regs __iomem * -> struct ftmac110_regs *

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
4 years agonet: ftmac110: Update license statement
Kuo-Jung Su [Wed, 10 Jul 2013 01:25:47 +0000 (09:25 +0800)]
net: ftmac110: Update license statement

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
4 years agonet.h: don't use the reserved name __unused
Jeroen Hofstee [Sat, 10 Aug 2013 14:52:47 +0000 (16:52 +0200)]
net.h: don't use the reserved name __unused

The __* keywords are reserved. On FreeBSD __unused evaluates
to the attribute unused, causing a compilation failure.
Just use unused instead.

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
cc: joe.hershberger@gmail.com

4 years agolinkstation_HGLAN: Convert from unused CONFIG_BOOTP_MASK to specific list
Tom Rini [Fri, 9 Aug 2013 19:58:18 +0000 (15:58 -0400)]
linkstation_HGLAN: Convert from unused CONFIG_BOOTP_MASK to specific list

Signed-off-by: Tom Rini <trini@ti.com>
4 years agogalaxy5200: Convert from unused CONFIG_BOOTP_MASK to specific list
Tom Rini [Fri, 9 Aug 2013 18:43:05 +0000 (14:43 -0400)]
galaxy5200: Convert from unused CONFIG_BOOTP_MASK to specific list

Signed-off-by: Tom Rini <trini@ti.com>
4 years agoconfigs: Remove unused CONFIG_BOOTP_DEFAULT
Tom Rini [Fri, 9 Aug 2013 18:39:51 +0000 (14:39 -0400)]
configs: Remove unused CONFIG_BOOTP_DEFAULT

Signed-off-by: Tom Rini <trini@ti.com>
4 years agonet: phy/realtek: Add support for RTL8211DN and RTL8211E phy modules
Bhupesh Sharma [Thu, 18 Jul 2013 08:28:20 +0000 (13:58 +0530)]
net: phy/realtek: Add support for RTL8211DN and RTL8211E phy modules

This patch adds support for Realtek PHY modules RTL8211DN and
RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG),
which can be found on Freescale's T1040RDB boards.

To make the driver more generic across 8211 family, a generic name 8211x
is added for macros and function names.

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
4 years agonet: smsc95xx: Add support for another SMSC95xx variant
Stefan Roese [Wed, 3 Jul 2013 16:34:54 +0000 (18:34 +0200)]
net: smsc95xx: Add support for another SMSC95xx variant

This patch adds support for the SMSC9500 with product id 0x9900 which is
equipped in the "EXSYS USB 2.0" etherner USB adapter.

Tested on omap3_beagle.

Signed-off-by: Stefan Roese <sr@denx.de>
4 years agonet: Use ARRAY_SIZE at appropriate places
Axel Lin [Wed, 3 Jul 2013 03:24:18 +0000 (11:24 +0800)]
net: Use ARRAY_SIZE at appropriate places

Use ARRAY_SIZE instead of having similar implementation in each drivers.
The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used
at all, so this patch removes it instead of converting it to use ARRAY_SIZE.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
4 years agophy: smsc: LAN8710/8720 are not Gbit PHYs
Fabio Estevam [Fri, 7 Jun 2013 00:04:19 +0000 (21:04 -0300)]
phy: smsc: LAN8710/8720 are not Gbit PHYs

LAN8710/8720 are 10/100 Mbps PHYs, so fix the '.features' field.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
4 years agoserial: arm_dcc: Convert to use default_serial_puts
Axel Lin [Sat, 17 Aug 2013 07:39:34 +0000 (15:39 +0800)]
serial: arm_dcc: Convert to use default_serial_puts

Use default_serial_puts() instead of its own implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
4 years agopowerpc/ppc4xx: Fix dlvision-10g reset gpio
Dirk Eibach [Fri, 9 Aug 2013 08:52:54 +0000 (10:52 +0200)]
powerpc/ppc4xx: Fix dlvision-10g reset gpio

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
4 years agopowerpc/ppc4xx: Do full iocon PHY initialization in software
Dirk Eibach [Fri, 9 Aug 2013 08:52:53 +0000 (10:52 +0200)]
powerpc/ppc4xx: Do full iocon PHY initialization in software

Up to this point some PHY initialization was done from the FPGA
and some from u-boot.
From now all initialization is done from u-boot.
To keep this maintainable a PHY setup machine was implemented that can
execute commands from initialization arrays.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
4 years agopowerpc/ppc4xx: Add support for iocon-2
Dirk Eibach [Fri, 9 Aug 2013 08:52:52 +0000 (10:52 +0200)]
powerpc/ppc4xx: Add support for iocon-2

Add a new iocon flavor with a second communiction port per channel.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
4 years agopowerpc/ppc4xx: Add support for iocon fiber
Dirk Eibach [Fri, 9 Aug 2013 08:52:51 +0000 (10:52 +0200)]
powerpc/ppc4xx: Add support for iocon fiber

Add a new iocon flavor with fiber instead of copper connectivity.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
4 years agoMerge branch 'master' of git://88.191.163.10/u-boot-arm
Tom Rini [Sun, 18 Aug 2013 18:14:34 +0000 (14:14 -0400)]
Merge branch 'master' of git://88.191.163.10/u-boot-arm

Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.

Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h

Signed-off-by: Tom Rini <trini@ti.com>
4 years agoMerge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Albert ARIBAUD [Sat, 17 Aug 2013 16:24:13 +0000 (18:24 +0200)]
Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

4 years agogpio: pca953x: Use ARRAY_SIZE instead of reinventing it
Axel Lin [Sat, 22 Jun 2013 10:22:48 +0000 (18:22 +0800)]
gpio: pca953x: Use ARRAY_SIZE instead of reinventing it

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
4 years agotools/Makefile: Move _GNU_SOURCE to Makefile
York Sun [Tue, 30 Jul 2013 22:26:11 +0000 (15:26 -0700)]
tools/Makefile: Move _GNU_SOURCE to Makefile

Commit 669dfc2e adds libfdt_env.h to HOSTCPPFLAGS. It causes stdio.h
to be included before _GNU_SOURCE is defined in C files. On some old hosts
some prototypes are protected by #ifdef __USE_GNU, which is set when
_GNU_SOURCE is defined.

Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
4 years agoimage: Display FIT timestamp when booting
Simon Glass [Wed, 17 Jul 2013 03:10:01 +0000 (20:10 -0700)]
image: Display FIT timestamp when booting

The timestamp is shown in fit_print_contents() but for some reason not
in fit_image_print(). This seems to be an oversight, since it is the latter
which is used by bootm.

Add timestamp printing in this case.

(There is code duplication in these two function, for looking at in a future
patch).

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agobootm: fix conditional controlling call to fixup_silent_linux
Paul B. Henson [Sun, 4 Aug 2013 04:29:09 +0000 (21:29 -0700)]
bootm: fix conditional controlling call to fixup_silent_linux

This function is only defined if CONFIG_SILENT_CONSOLE is set and
CONFIG_SILENT_U_BOOT_ONLY is not set, the call to it should be based
on the same conditions.

Signed-off-by: Paul B. Henson <henson@acm.org>
Acked-by: Simon Glass <sjg@chromium.org>
4 years agoRFC: bootm: Add silent_linux environment variable
Simon Glass [Wed, 17 Jul 2013 03:10:00 +0000 (20:10 -0700)]
RFC: bootm: Add silent_linux environment variable

At present the console for linux is silent if the U-Boot console is silent,
unless CONFIG_SILENT_U_BOOT_ONLY is set. I wonder if a better way would be
to have an environment variable to control this? Then we can control the
verbosity from scripts, and set the variable to 'no' for those boards that
want Linux to boot with console output.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agoSPL: Limit image name print length
Taras Kondratiuk [Tue, 16 Jul 2013 11:45:01 +0000 (14:45 +0300)]
SPL: Limit image name print length

If image name is longer than 32 bytes, then it will be truncated.
This will remove '\0' at the end of the line, so printf will
go out of string limit.

Signed-off-by: Taras Kondratiuk <taras@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
4 years agoEnable xmodem support
Angus Ainslie [Wed, 26 Jun 2013 22:54:24 +0000 (16:54 -0600)]
Enable xmodem support

This is a trivial patch that just enables xmodem downloads using the existing
ymodem framework.

Signed-off-by: Angus Ainslie <angus@akkea.ca>
4 years agoAdd TI816X evm board support
TENART Antoine [Tue, 2 Jul 2013 10:06:00 +0000 (12:06 +0200)]
Add TI816X evm board support

Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Change to SPDX, fix a few compiler warnings, adapt to
CONFIG_OMAP_COMMON]
Signed-off-by: Tom Rini <trini@ti.com>
4 years agoAdd TI816X support
TENART Antoine [Tue, 2 Jul 2013 10:05:59 +0000 (12:05 +0200)]
Add TI816X support

Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
4 years agoPrepare for TI816X : reuse existing code from TI814X
TENART Antoine [Tue, 2 Jul 2013 10:05:58 +0000 (12:05 +0200)]
Prepare for TI816X : reuse existing code from TI814X

Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX

Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
4 years agoarm, da850: add ipam390 board support
Heiko Schocher [Mon, 5 Aug 2013 14:00:38 +0000 (16:00 +0200)]
arm, da850: add ipam390 board support

add the am1808 based ipam390 board from Barix.

- 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM
  interface
- 128MByte, NAND Flash, 8bit databus to the NANDFlash
  Interface
- Ethernet PHY Micrel KSZ8051R via RMII
- Console on UART 0
- booting fron nand flash
- spl falcon bootmode

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
4 years agoarm, da850: enable the correct uart in arch_cpu_init()
Heiko Schocher [Mon, 5 Aug 2013 14:00:37 +0000 (16:00 +0200)]
arm, da850: enable the correct uart in arch_cpu_init()

in arch_cpu_init() uart2 is fix enabled, without reference the
setting from CONFIG_SYS_NS16550_COM1. Use the setting from
CONFIG_SYS_NS16550_COM1 for enabling the console.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
4 years agobootstage: get more BOOTSTAGE_ID* in show_boot_progress()
Heiko Schocher [Mon, 5 Aug 2013 14:00:36 +0000 (16:00 +0200)]
bootstage: get more BOOTSTAGE_ID* in show_boot_progress()

In case CONFIG_BOOTSTAGE is not defined, call from bootstage_mark_name()
show_boot_progress(), so get more BOOTSTAGE_ID* ids in show_boot_progress()
if CONFIG_BOOTSTAGE is not defined.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
4 years agoarm/davinci/da850: add uart0_pins_rtscts and RMII_MHz_50_CLK in emac_pins_rmii pinmux
Heiko Schocher [Mon, 5 Aug 2013 14:00:35 +0000 (16:00 +0200)]
arm/davinci/da850: add uart0_pins_rtscts and RMII_MHz_50_CLK in emac_pins_rmii pinmux

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
4 years agoTI:armv7: Enable CONFIG_CMD_GPIO
Tom Rini [Fri, 9 Aug 2013 15:22:20 +0000 (11:22 -0400)]
TI:armv7: Enable CONFIG_CMD_GPIO

Add the generic "poke a GPIO" command, with the GPIO related defines.

Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
4 years agoTI:armv7: Enable CONFIG_CMD_SPI
Tom Rini [Fri, 9 Aug 2013 15:22:19 +0000 (11:22 -0400)]
TI:armv7: Enable CONFIG_CMD_SPI

Add the generic "poke the SPI bus" command, with the SPI related
defines.

Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
4 years agoTI:omap5/dra7xx: Convert to ti_armv7_common.h
Tom Rini [Fri, 9 Aug 2013 15:22:18 +0000 (11:22 -0400)]
TI:omap5/dra7xx: Convert to ti_armv7_common.h

Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly.  The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.

Signed-off-by: Tom Rini <trini@ti.com>
4 years agoTI:am33xx: Create common config files for TI ARMv7 platforms, and AM33xx
Tom Rini [Fri, 9 Aug 2013 15:22:17 +0000 (11:22 -0400)]
TI:am33xx: Create common config files for TI ARMv7 platforms, and AM33xx

We create two new files, include/configs/ti_armv7_common.h for all of
the common IP blocks and related features / commands we share in
virtually all of our platforms.  We then create
include/configs/ti_am335x_common.h for everything common to the am335x
SoC leaving just the board specific parts to
include/configs/ti_am335x_common.h.

Signed-off-by: Tom Rini <trini@ti.com>
4 years agoam335x_evm: Bring in 'boot_fdt' logic from i.MX
Tom Rini [Fri, 9 Aug 2013 15:22:16 +0000 (11:22 -0400)]
am335x_evm: Bring in 'boot_fdt' logic from i.MX

Bring in the 'boot_fdt' environment variable that i.MX boards use to try
and load a device tree when booting.

Signed-off-by: Tom Rini <trini@ti.com>
4 years agoarm: spl: For Falcon Mode, set a default machid of ~0
Tom Rini [Fri, 9 Aug 2013 15:22:15 +0000 (11:22 -0400)]
arm: spl: For Falcon Mode, set a default machid of ~0

With device trees, boards do not always set CONFIG_MACH_TYPE now, so we
must not rely on this define being set.  The kernel uses ~0 to see if we
have a valid machine number or not, so set that as the default, invalid
machine, id and only fix if CONFIG_MACH_TYPE is set.

Acked-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@ti.com>
4 years agoam335x_evm: Use default baud rate table
Tom Rini [Fri, 9 Aug 2013 15:22:14 +0000 (11:22 -0400)]
am335x_evm: Use default baud rate table

Signed-off-by: Tom Rini <trini@ti.com>
4 years agoam33xx: Stop using PHYS_DRAM_1 define
Tom Rini [Fri, 9 Aug 2013 15:22:13 +0000 (11:22 -0400)]
am33xx: Stop using PHYS_DRAM_1 define

We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this
for CONFIG_SYS_SDRAM_BASE.  But then we kept on referencing PHYS_DRAM_1
in other places.  Change to directly setting CONFIG_SYS_DRAM_BASE and
then using that name in code.

Signed-off-by: Tom Rini <trini@ti.com>