nm-kernel:u-boot-nm.git
3 years agoupdate to ensure we can stop it with a space old-ti-bootloader/zoom1/part-1-chain-boot-upstream-u-boot
Nishanth Menon [Fri, 25 Apr 2014 19:08:41 +0000 (14:08 -0500)]
update to ensure we can stop it with a space

Signed-off-by: Nishanth Menon <nm@ti.com>
3 years agolab: upstream u-boot support
Nishanth Menon [Fri, 25 Apr 2014 18:06:18 +0000 (13:06 -0500)]
lab: upstream u-boot support

Signed-off-by: Nishanth Menon <nm@ti.com>
8 years agoDo one time check if debug board is connected or not to Zoom2.
Vikram Pandita [Thu, 19 Feb 2009 05:54:24 +0000 (23:54 -0600)]
Do one time check if debug board is connected or not to Zoom2.
The GPIO_158 line is valid only initially for detection of
dbg board attached or not.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
8 years agoAllow Red led to blink when T2 Battery charging in enabled in u-boot
Vikram Pandita [Thu, 19 Feb 2009 00:39:45 +0000 (18:39 -0600)]
Allow Red led to blink when T2 Battery charging in enabled in u-boot
This is needed on zoom2 to confirm that GPBR1 register of t2 has
been set to 0x90 to allow for Automatic AC charging.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
8 years agou-boot Add runtime check for debug board on Zoom2.
Tom Rix [Tue, 17 Feb 2009 23:19:37 +0000 (17:19 -0600)]
u-boot Add runtime check for debug board on Zoom2.

Query GPIO 158 to check if the debug board is connected.
Wrap serial with this check because UART is on debug board.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
8 years agou-boot Add gpio support.
Tom Rix [Tue, 17 Feb 2009 19:14:51 +0000 (13:14 -0600)]
u-boot Add gpio support.

Framework was from public u-boot-arm repository.
Some defines added to demystifiy the clock setup.
The led code which had been mux based was changed over to gpio.
At u-boot prompt, the blue led is on.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
8 years agou-boot : Zoom2 support CONFIG_SERIAL_MULTI
Tom Rix [Tue, 17 Feb 2009 19:09:22 +0000 (13:09 -0600)]
u-boot : Zoom2 support CONFIG_SERIAL_MULTI

Zoom2 serial is supplied by a uart on the debug board.
This patch enables the user to select which of the 4 uarts to use.

This patch also isolates Zoom2 serial to support future improvements
without having to pollute the general serial driver.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
8 years agoEnable high currnet AC charging on Zoom2
Vikram Pandita [Wed, 11 Feb 2009 15:02:00 +0000 (09:02 -0600)]
Enable high currnet AC charging on Zoom2

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
8 years agoU-Boot Limit fastboot compile
Tom Rix [Tue, 10 Feb 2009 13:55:36 +0000 (07:55 -0600)]
U-Boot Limit fastboot compile

If fastboot is not configured, do not compile.
Some fixes for macros that provide the default fastboot interface.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
8 years agoEnable AC charging on Zoom2
Vikram Pandita [Tue, 10 Feb 2009 00:17:32 +0000 (18:17 -0600)]
Enable AC charging on Zoom2

Patch enables AC charging in u-boot.
Automatic Main Charging is not working on zoom2 as T2 register
GPBR1 reset value is 0x00. It should be 0x90

To indicate that AC charging is enabled, the RED LED is blinked.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
8 years agoEnable IDCC modem gpio on zoom2
Vikram Pandita [Tue, 10 Feb 2009 00:05:56 +0000 (18:05 -0600)]
Enable IDCC modem gpio on zoom2

This patch enables GPIO 110 and 103 to enable IDCC modem on zoom2

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
8 years agou-boot : Zoom2 Status LED
Tom Rix [Mon, 9 Feb 2009 23:49:59 +0000 (17:49 -0600)]
u-boot : Zoom2 Status LED

The red led on the zoom2 now blinks durning the
fastboot usb discovery.

If it stays red you have problems.
Disconnect / reconnect cables
Cycle power.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
8 years agoFix for 2008q3 fastboot reg accesses need to be volatile
Tom Rix [Fri, 6 Feb 2009 00:27:03 +0000 (18:27 -0600)]
Fix for 2008q3 fastboot reg accesses need to be volatile

The problem is with the fastboot feature.
It uses method similar to mmc for accessing memory mapped registers.
When you switch to the 2008q3 toolchain, it is necessary to add
'volatile' to the declaration.
The problem was verified and the fix tested on a zoom1/ldp board.
Tom

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
8 years agoFix mmc registers to be volatile
Tom Rix [Fri, 6 Feb 2009 00:26:58 +0000 (18:26 -0600)]
Fix mmc registers to be volatile

This fixes a reported problem with 2008q3 toolchain.

In general all memory mapped registers should be volatile.
Other changes are fomatting changes.

Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
8 years agoChange CPPFLAGS from building with 2008q3 tool chain.
Tom Rix [Fri, 6 Feb 2009 00:26:53 +0000 (18:26 -0600)]
Change CPPFLAGS from building with 2008q3 tool chain.

Tool chain can be downloaded from:
http://www.codesourcery.com/gnu_toolchains/arm/releases/2008q3

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
8 years agoGetting Android USB Fast boot working for Zoom2 and Zoom1
Vikram Pandita [Mon, 2 Feb 2009 22:47:47 +0000 (16:47 -0600)]
Getting Android USB Fast boot working for Zoom2 and Zoom1

This patch implements the USB protocol described at:

http://android.git.kernel.org/?p=platform/bootloader/legacy.git;
a=blob;f=fastboot_protocol.txt;
h=2248992d26d5077a28d803e32057f83abb315d21;
hb=d08c9e9444e2fb688ca4d3c4d807ba69c680fb3c

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Tested-by: Vikram Pandita <vikram.pandita@ti.com>
8 years agoFix compilation error for Zoom2 platform after renaming of files
Vikram Pandita [Wed, 7 Jan 2009 23:10:39 +0000 (17:10 -0600)]
Fix compilation error for Zoom2 platform after renaming of files

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
8 years agoU-Boot:Change zoom2 file name
Nishanth Menon [Tue, 6 Jan 2009 15:54:01 +0000 (09:54 -0600)]
U-Boot:Change zoom2 file name

Change zoom2 board file name from sdp.c to labrador.c

Signed-off-by: Nishanth Menon <nm@ti.com>
8 years agoU-Boot:OMAP3:Add Additional SDRC register definitions, enable cke1
Nishanth Menon [Tue, 6 Jan 2009 15:44:01 +0000 (09:44 -0600)]
U-Boot:OMAP3:Add Additional SDRC register definitions, enable cke1

This patch adds CS1 definitions for SDRC definitions on OMAP3
This further enables cke1 definitions for zoom2.

This patch contains fixes to the sdrc reg definitions by Santosh.

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
8 years agoU-boot pad config to support MMC 8-bit
Madhusudhan Chikkature [Wed, 17 Dec 2008 18:00:47 +0000 (12:00 -0600)]
U-boot pad config to support MMC 8-bit

pad config changes in u-boot required to configure MMC4 to MMC7 data lines

Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
8 years agoAdd Serial Quad UART (TL16CP754C) support to Zoom2 board
Vikram Pandita [Fri, 14 Nov 2008 02:26:48 +0000 (20:26 -0600)]
Add Serial Quad UART (TL16CP754C) support to Zoom2 board

On Zoom2 board:
OMAP Uart1 goes to Modem
OMAP Uart2 goes to Bluetooth
OMAP Uart3 goes to GPS

For debug uart, an external serial device is installed on GPMC CS3.
This is available on the debug board that will get attached to Zoom2.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
9 years agoFix compilation warnings in u-boot
Janorkar, Mayuresh [Tue, 18 Nov 2008 22:48:12 +0000 (16:48 -0600)]
Fix compilation warnings in u-boot

Fix compilation warnings in u-boot that were not correclty fixed earlier

Signed-off-by: Janorkar, Mayuresh <mayur@ti.com>
9 years agonand unlock is valide for zoom2 platform as well.
Vikram Pandita [Thu, 20 Nov 2008 01:17:50 +0000 (19:17 -0600)]
nand unlock is valide for zoom2 platform as well.

Somehow the unlock command is implemented for limited number of platforms
so it was missed for zoom2

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
9 years agoCleanup File: include/configs/omap3430zoom2.h
Vikram Pandita [Thu, 13 Nov 2008 23:45:36 +0000 (17:45 -0600)]
Cleanup File: include/configs/omap3430zoom2.h

Do not make this file dependent on Labrador platform.
Zoom2 is independent platform and so remove dependency on LAB.

For adding the QUART support for console, lot of changes are required
to the config file and so a clean new config file is good to start for Zoom2.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
9 years agoThis patch sets the proper padconfig value for wvga spi chip select
Leed Salim Aguilar [Wed, 12 Nov 2008 20:41:14 +0000 (14:41 -0600)]
This patch sets the proper padconfig value for wvga spi chip select

Also DVI power enable (gpio_167) is set as ouptut

Signed-off-by: Leed Aguilar <leed.aguilar@ti.com>
9 years agoThis patch allows booting from mmc.
Vikram Pandita [Wed, 12 Nov 2008 14:26:38 +0000 (08:26 -0600)]
This patch allows booting from mmc.

The previous state was sending the following message:
** Can't read from device 0 **

Fix the warning while compiling the file.

Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Leed Aguilar <leed.aguilar@ti.com>
9 years agoFrom: Leed Aguilar <leed.aguilar@ti.com>
Vikram Pandita [Tue, 11 Nov 2008 22:17:14 +0000 (16:17 -0600)]
From: Leed Aguilar <leed.aguilar@ti.com>

[PATCH][UBOOT]mmcinit: Can't read from device 0

This patch allows booting from mmc.
The previous state was sending the following message:
** Can't read from device 0 **

Signed-off-by: Leed Aguilar <leed.aguilar@ti.com>
9 years agoThis patch is needed by some of the nand devices like Micron MT29FxGxxxxx
Vikram Pandita [Mon, 10 Nov 2008 18:36:31 +0000 (12:36 -0600)]
This patch is needed by some of the nand devices like Micron MT29FxGxxxxx
Earlier patch by vimal e9de7da4de82d3b6cfa introduced a reset much below
in the function

This reset is needed for MMC booting, else at times NAND id is not
recognized by u-boot, throwing following error message:

[snip]
NAND:NAND device: Manufacturer ID: 0x2c, Chip ID: 0x01
(<> AND 128MiB 3,3V 8-bit)
NAND bus width 16 instead 8 bit 0 MiB

Could not read entire image due to bad blocks
*** Warning - bad CRC or NAND, using default environment
[snip-end]

9 years agoDo not hard-code the mac-address of LAN92xxx ethernet device.
Vikram Pandita [Mon, 10 Nov 2008 16:12:17 +0000 (10:12 -0600)]
Do not hard-code the mac-address of LAN92xxx ethernet device.
Take the mac address from 'ethaddr' u-boot environment variable.

If there is no mac-address programmed in EEPROM and
there is no ethaddr environmane variable,
User will be shown error message:

*** ERROR: Mac id is not programmed in EEPROM
        setenv ethaddr 'xx:xx:xx:xx:xx:xx';saveenv
 Then reboot u-boot for NFS to work

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
9 years agoThis patch will cause u-boot to pass OMAP_ZOOM2(1967) mach id to kernel.
Vikram Pandita [Fri, 7 Nov 2008 22:33:11 +0000 (16:33 -0600)]
This patch will cause u-boot to pass OMAP_ZOOM2(1967) mach id to kernel.

So make sure that the kernel is compiled with omap_zoom2_defconfig
otherwise kernel will not boot up.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
9 years agoAdd u-boot.lds file for zoom2 platform
Vikram Pandita [Fri, 7 Nov 2008 20:37:24 +0000 (14:37 -0600)]
Add u-boot.lds file for zoom2 platform

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
9 years ago.gitignore had a wildcard entry for uboot.*
Vikram Pandita [Fri, 7 Nov 2008 20:35:43 +0000 (14:35 -0600)]
.gitignore had a wildcard entry for uboot.*
we need to track file u-boot.lds
so remove that wildcard entry.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
9 years agoFollowing patch gives a workaround for NFS mount to work on Zoom2
Vikram Pandita [Thu, 6 Nov 2008 04:47:24 +0000 (22:47 -0600)]
Following patch gives a workaround for NFS mount to work on Zoom2

Alpha Zoom2 boards do not have MAC address programmed for LAN9221.
In that case assign a default mac address 00:08:ee:02:53:fc

Final(Beta) Zoom2 board should not have this issue.

There is run time check not to execute this workaround
if MAC address is correctly populated.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
9 years agoChange u-boot prompt to "OMAP34XX ZOOM2 # " for zoom2 platform
Vikram Pandita [Tue, 4 Nov 2008 18:39:42 +0000 (12:39 -0600)]
Change u-boot prompt to "OMAP34XX ZOOM2 # " for zoom2 platform

Signed-off-by: vikram pandita <vikram.pandita@ti.com>
9 years agoU-boot for Zoom2 can be built using config: omap3430zoom2_config
Vikram Pandita [Tue, 4 Nov 2008 18:26:25 +0000 (12:26 -0600)]
U-boot for Zoom2 can be built using config: omap3430zoom2_config

Major changes to u-boot:
        + LAN9221 is the ethernet IC
        + LAN9221 is connected to CS7 of GPMC
        + NAND part is new: MT29F4G16ABC - 4Gb NAND
        + Change Mux settings for new NAND and LAN parts

Signed-off-by: vikram pandita <vikram.pandita@ti.com>
9 years agoAdding a chip reset after power-up
vimal singh [Fri, 31 Oct 2008 05:59:34 +0000 (00:59 -0500)]
Adding a chip reset after power-up

Before any NAND cmd, reset cmd is  required by some nand chips (e.g.
Micron MT29FxGxxxxx) before any access to chip.

Signed-off-by: vimal singh <vimal.singh@ti.com>
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
9 years agoAdd support for Micron NAND part MT29F4G16ABC
Vikram Pandita [Fri, 31 Oct 2008 01:24:51 +0000 (20:24 -0500)]
Add support for Micron NAND part MT29F4G16ABC
This is a 4Gb 16-bit NAND used on Zoom2 board

Signed-off-by: vikram pandita <vikram.pandita@ti.com>
9 years agoFix error introduced in LAN driver while fixing warning
Vikram Pandita [Fri, 31 Oct 2008 01:11:14 +0000 (20:11 -0500)]
Fix error introduced in LAN driver while fixing warning

Following error is fixed on doing tftp/dhcp
LAN9x18 (0x92110000) detected.
Read mac address: 00:08:EE:02:50:54
start Auto negotiation... (take ~2sec)
Auto negotiation complete, 100BaseTX, full duplex
BOOTP broadcast 1
lan9118_read: read buffers full!
lan9118_read: read buffers full!
BOOTP broadcast 2
lan9118_read: read buffers full!
lan9118_read: read buffers full!

Signed-off-by: vikram pandita <vikram.pandita@ti.com>
9 years agoFixed a missed generated file in .gitignore
Keith Deacon [Mon, 13 Oct 2008 19:46:53 +0000 (14:46 -0500)]
Fixed a missed generated file in .gitignore

9 years agoFixup to make git play nice
Keith Deacon [Mon, 13 Oct 2008 19:43:26 +0000 (14:43 -0500)]
Fixup to make git play nice

9 years agoMega patch to sync U-BOOT-114 base with current OMAP U-Boot RLS_5.03
Keith Deacon [Mon, 13 Oct 2008 19:24:09 +0000 (14:24 -0500)]
Mega patch to sync U-BOOT-114 base with current OMAP U-Boot RLS_5.03

11 years agoMerge with /home/sr/git/u-boot U-Boot-1_1_4
Wolfgang Denk [Fri, 16 Dec 2005 16:39:27 +0000 (17:39 +0100)]
Merge with /home/sr/git/u-boot

11 years agoMPC5200: Set PCI retry counter to 0 = infinite retry;
Wolfgang Denk [Fri, 16 Dec 2005 14:14:18 +0000 (15:14 +0100)]
MPC5200:  Set PCI retry counter to 0 = infinite retry;
The default of 255 is too short for slow devices.
Patch by Martin Nykodym, 12 Dec 2005

11 years agoChanges to Yellowstone & Yosemite 440EP/GR eval boards:
Stefan Roese [Thu, 15 Dec 2005 08:43:12 +0000 (09:43 +0100)]
Changes to Yellowstone & Yosemite 440EP/GR eval boards:
- Changed GPIO setup to enable another address line in order to
  address 64M of FLASH.
- Added function sdram_tr1_set to auto calculate the tr1 value for
  the DDR.
Patch by Steven Blakeslee, 12 Dec 2005

11 years agoMerge with /home/m8/git/u-boot
Wolfgang Denk [Wed, 14 Dec 2005 14:05:59 +0000 (15:05 +0100)]
Merge with /home/m8/git/u-boot

11 years ago(no commit message)
Wolfgang Denk [Mon, 12 Dec 2005 15:06:05 +0000 (16:06 +0100)]

11 years agoChange port configuration for O2DNT (CODEC1 on PSC1)
Marian Balakowicz [Tue, 6 Dec 2005 19:33:07 +0000 (20:33 +0100)]
Change port configuration for O2DNT (CODEC1 on PSC1)

11 years agoFix DPRAM offset/size for MPC8541/8555.
Wolfgang Denk [Tue, 6 Dec 2005 14:02:31 +0000 (15:02 +0100)]
Fix DPRAM offset/size for MPC8541/8555.
Simplify TQM85xx Makefile handling.

11 years agoFix data overflow (typo?) in rtc/ds1302.c
Wolfgang Denk [Sun, 4 Dec 2005 10:20:57 +0000 (11:20 +0100)]
Fix data overflow (typo?) in rtc/ds1302.c

11 years agoCode cleanup, especially MIPS for GCC 4.x
Wolfgang Denk [Sat, 3 Dec 2005 23:40:34 +0000 (00:40 +0100)]
Code cleanup, especially MIPS for GCC 4.x

11 years agoFix U-Boot compilation for MIPS boards using ELDK 4.0
Wolfgang Denk [Thu, 1 Dec 2005 01:15:07 +0000 (02:15 +0100)]
Fix U-Boot compilation for MIPS boards using ELDK 4.0

11 years agoMerge with /home/sr/git/u-boot
Wolfgang Denk [Thu, 1 Dec 2005 00:38:13 +0000 (01:38 +0100)]
Merge with /home/sr/git/u-boot

11 years agoAdjust TQM834x PHY addresses for latest hardware revision.
Wolfgang Denk [Thu, 1 Dec 2005 00:17:24 +0000 (01:17 +0100)]
Adjust TQM834x PHY addresses for latest hardware revision.

11 years agoIncrease malloc arena on TQM5200 board to 256 kB.
Wolfgang Denk [Wed, 30 Nov 2005 23:55:19 +0000 (00:55 +0100)]
Increase malloc arena on TQM5200 board to 256 kB.
With 64 kb uniform flash sector size the old value of 128 kB was
too small.

11 years agoFix miiphy global data initialization (problem on 4xx boards when no
Marian Balakowicz [Wed, 30 Nov 2005 17:06:04 +0000 (18:06 +0100)]
Fix miiphy global data initialization (problem on 4xx boards when no
ethaddr is assigned). Initialization moved from miiphy_register() to
eth_initialize().

Based on initial patch for 4xx platform by Matthias Fuchs.

11 years agoAdd support for TQM8541/8555 boards, TQM85xx support reworked:
Stefan Roese [Wed, 30 Nov 2005 12:06:40 +0000 (13:06 +0100)]
Add support for TQM8541/8555 boards, TQM85xx support reworked:

- Support for TQM8541/8555 boards added.
- Complete rework of TQM8540/8560 support.
- Common TQM85xx code now supports all current TQM85xx platforms
  (TQM8540/8541/8555/8560).
- DDR SDRAM size detection added.
- CAS latency default values can be overwritten by setting "serial#"
  to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used.
  If problems are detected with this non default CAS latency,
  the defualt values will be used instead.
- FLASH size detection added.
- Moved FCC ethernet driver initialization behind TSEC driver init
  -> TSEC is first device.

Patch by Stefan Roese, 30 Nov 2005

11 years agoCompile warning fixed
Stefan Roese [Tue, 29 Nov 2005 18:13:38 +0000 (19:13 +0100)]
Compile warning fixed
Patch by Stefan Roese, 29 Nov 2005

11 years agoAdd support for AMCC 440SP, add support for AMCC Luan 440SP eval board.
Stefan Roese [Tue, 29 Nov 2005 17:18:21 +0000 (18:18 +0100)]
Add support for AMCC 440SP, add support for AMCC Luan 440SP eval board.
Patch by John Otken, 23 Nov 2005

11 years agoMinor AMCC 4xx board cleanups
Stefan Roese [Tue, 29 Nov 2005 17:17:41 +0000 (18:17 +0100)]
Minor AMCC 4xx board cleanups
Patch by Stefan Roese, 27 Nov 2005

11 years agoIncrease IPB and PCI clocks for O2DNT board.
Marian Balakowicz [Sun, 27 Nov 2005 19:15:41 +0000 (20:15 +0100)]
Increase IPB and PCI clocks for O2DNT board.

11 years agoChanged PPC44x startup message (cpu info, speed...) to common style:
Stefan Roese [Sun, 27 Nov 2005 18:36:26 +0000 (19:36 +0100)]
Changed PPC44x startup message (cpu info, speed...) to common style:

On PPC44x platforms, the startup message generated in "cpu.c" only
comprised the ppc type and revision but not additional informations
like speed etc. Those speed infos where printed in the board specific
code. This new implementation now prints all CPU infos in the common
cpu specific code. No board specific code is needed anymore and
therefore removed from all current 44x implementations.

Patch by Stefan Roese, 27 Nov 2005

11 years agoRemove unnnecessary #include <linux/types.h> from include/asm-*/u-boot.h
Wolfgang Denk [Fri, 25 Nov 2005 15:38:03 +0000 (16:38 +0100)]
Remove unnnecessary #include <linux/types.h> from include/asm-*/u-boot.h

12 years agoAllow use of include/image.h and include/asm-*/u-boot.h in proprietary code.
Wolfgang Denk [Fri, 25 Nov 2005 09:38:43 +0000 (10:38 +0100)]
Allow use of include/image.h and include/asm-*/u-boot.h in proprietary code.
The COPYING file was extended to make clear that these files can be
used in non-GPL code, too.

12 years agoAdd support for Prodrive P3P440 board:
Stefan Roese [Tue, 22 Nov 2005 12:20:42 +0000 (13:20 +0100)]
Add support for Prodrive P3P440 board:
- Added onboard PPC440 DDR autodetection in cpu/ppc/sdram.c
- CFG_FLASH_QUIET_TEST added to use the common CFI driver
  for bank autodetection
Patch by Stefan Roese, 22 Nov 2005

12 years agoChange all '$(...)' variable references into '${...}'
Wolfgang Denk [Sun, 20 Nov 2005 20:40:11 +0000 (21:40 +0100)]
Change all '$(...)' variable references into '${...}'
which makes the environment compatible with the hush shell.
WARNING: Support for the old '$(...)' syntax will be
discontinued in a later version.

12 years agoMinor changes to init flags in TQM834x PCI.
Rafal Jaworowski [Wed, 16 Nov 2005 23:26:18 +0000 (00:26 +0100)]
Minor changes to init flags in TQM834x PCI.

12 years agoAdd CHANGELOG entry
Stefan Roese [Tue, 15 Nov 2005 15:26:34 +0000 (16:26 +0100)]
Add CHANGELOG entry
Patch by Stefan Roese, 15 Nov 2005

12 years agoMerge with /server/home/stefan/git/u-boot/bamboo-sdram
Stefan Roese [Tue, 15 Nov 2005 15:23:41 +0000 (16:23 +0100)]
Merge ... /server/home/stefan/git/u-boot/bamboo-sdram

12 years agoFix Bamboo DDR SDRAM initialization (problem with onboard SDRAM)
Stefan Roese [Tue, 15 Nov 2005 15:04:58 +0000 (16:04 +0100)]
Fix Bamboo DDR SDRAM initialization (problem with onboard SDRAM)
Patch by Stefan Roese, 15 Nov 2005

12 years agoNew PPC 405EP board added: CMS700
Stefan Roese [Tue, 15 Nov 2005 09:35:59 +0000 (10:35 +0100)]
New PPC 405EP board added: CMS700
Added CONFIG_NET_MULTI for VOM405 board.
Added reset_phy() for VOM405 board.
Patch by Matthias Fuchs, 09 Nov 2005

12 years agoAdd explanation for CDP checksum algorithm
Wolfgang Denk [Thu, 10 Nov 2005 19:59:46 +0000 (20:59 +0100)]
Add explanation for CDP checksum algorithm

12 years agoUpdated PCI mapping for esd CPCI2DP board.
Stefan Roese [Tue, 8 Nov 2005 08:00:09 +0000 (09:00 +0100)]
Updated PCI mapping for esd CPCI2DP board.
Add support for error LED.
Patch by Matthias Fuchs, 07 Nov 2005

12 years agoFix MPC85xx PCI support (pci_register_hose() before pci config access)
Stefan Roese [Mon, 7 Nov 2005 12:43:06 +0000 (13:43 +0100)]
Fix MPC85xx PCI support (pci_register_hose() before pci config access)
Patch by Stefan Roese, 07 Nov 2005

12 years agoCorrect PPC Timebase register definitions (SPRN_TBRL...)
Stefan Roese [Mon, 7 Nov 2005 08:57:57 +0000 (09:57 +0100)]
Correct PPC Timebase register definitions (SPRN_TBRL...)
Patch by Stefan Roese, 07 Nov 2005

12 years agoAdjust bd->bi_flashstart on Yellowstone & Yosemite to correct size
Stefan Roese [Sat, 5 Nov 2005 14:50:16 +0000 (15:50 +0100)]
Adjust bd->bi_flashstart on Yellowstone & Yosemite to correct size
Patch by Stefan Roese, 05 Nov 2005

12 years agoAdjust TQM85x PHY addresses for latest hardware revision.
Wolfgang Denk [Thu, 3 Nov 2005 10:31:36 +0000 (11:31 +0100)]
Adjust TQM85x PHY addresses for latest hardware revision.

12 years agoAdditional fix for external IRQ config on Yellowstone & Yosemite
Stefan Roese [Thu, 3 Nov 2005 07:31:33 +0000 (08:31 +0100)]
Additional fix for external IRQ config on Yellowstone & Yosemite
Patch by Stefan Roese, 03 Nov 2005

12 years agoAdd support for Ocotea pass 3 with 440GX Rev. F
Stefan Roese [Tue, 1 Nov 2005 09:08:03 +0000 (10:08 +0100)]
Add support for Ocotea pass 3 with 440GX Rev. F
Patch by Stefan Roese, 01 Nov 2005

12 years agoMerge with /git/u-boot.git
Stefan Roese [Tue, 1 Nov 2005 09:02:21 +0000 (10:02 +0100)]
Merge with /git/u-boot.git

12 years agoMore verbose CHANGELOG entry. DENX-2005-10-29-2350
Wolfgang Denk [Sat, 29 Oct 2005 21:50:20 +0000 (23:50 +0200)]
More verbose CHANGELOG entry.

12 years agoMerge with /home/m8/git/u-boot
Wolfgang Denk [Sat, 29 Oct 2005 21:45:04 +0000 (23:45 +0200)]
Merge with /home/m8/git/u-boot

12 years agoAdd missing CHANGELOG entries.
Marian Balakowicz [Sat, 29 Oct 2005 12:48:59 +0000 (14:48 +0200)]
Add missing CHANGELOG entries.

12 years agoAdd support for multiple PHYs.
Marian Balakowicz [Fri, 28 Oct 2005 20:30:33 +0000 (22:30 +0200)]
Add support for multiple PHYs.

12 years agoCorrect includes for flat tree builder.
Marian Balakowicz [Fri, 28 Oct 2005 16:08:03 +0000 (18:08 +0200)]
Correct includes for flat tree builder.

12 years agoFix conflicting types (flash_write()) in trab auto_update.c
Marian Balakowicz [Fri, 28 Oct 2005 13:29:43 +0000 (15:29 +0200)]
Fix conflicting types (flash_write()) in trab auto_update.c

12 years agoFix external IRQ configuration on Yellowstone & Yosemite
Stefan Roese [Fri, 28 Oct 2005 10:21:06 +0000 (12:21 +0200)]
Fix external IRQ configuration on Yellowstone & Yosemite

The multiplexed signals Ext IRQ0...3 have to be configured as IRQ,
because they default to GPIOx (440EP/GR).

Patch by Stefan Roese, 28 Oct 2005

12 years agoMerge with /home/wd/git/u-boot/master
Wolfgang Denk [Fri, 21 Oct 2005 20:41:25 +0000 (22:41 +0200)]
Merge with /home/wd/git/u-boot/master

12 years agoAdd missing 4xx board to MAKEALL
Stefan Roese [Thu, 20 Oct 2005 14:40:17 +0000 (16:40 +0200)]
Add missing 4xx board to MAKEALL
Patch by Stefan Roese, 20 Oct 2005

12 years agoFix conflicting types (flash_write()) in esd auto_update.c
Stefan Roese [Thu, 20 Oct 2005 14:39:16 +0000 (16:39 +0200)]
Fix conflicting types (flash_write()) in esd auto_update.c
Patch by Stefan Roese, 20 Oct 2005

12 years agoFix problem with sleep in NetConsole (use get_timer())
Stefan Roese [Thu, 20 Oct 2005 14:36:44 +0000 (16:36 +0200)]
Fix problem with sleep in NetConsole (use get_timer())
Patch by Stefan Roese, 20 Oct 2005

12 years agoAdd NetConsole Support for AMCC eval boards
Stefan Roese [Thu, 20 Oct 2005 14:34:28 +0000 (16:34 +0200)]
Add NetConsole Support for AMCC eval boards
Patch by Stefan Roese, 20 Oct 2005

12 years agoFix NetConsole support on 4xx (only print eth link on 1st transfer)
Stefan Roese [Tue, 18 Oct 2005 17:17:12 +0000 (19:17 +0200)]
Fix NetConsole support on 4xx (only print eth link on 1st transfer)
Patch by Stefan Roese, 18 Oct 2005

12 years agoAdd PCI support for the TQM834x board.
Rafal Jaworowski [Mon, 17 Oct 2005 00:39:53 +0000 (02:39 +0200)]
Add PCI support for the TQM834x board.

12 years agoFix typo.
Wolfgang Denk [Sun, 16 Oct 2005 22:24:00 +0000 (00:24 +0200)]
Fix typo.

12 years agoMerge with /home/sr/git/u-boot
Wolfgang Denk [Sun, 16 Oct 2005 22:19:16 +0000 (00:19 +0200)]
Merge with /home/sr/git/u-boot

12 years agoAdd missing CHANGELOG entry.
Wolfgang Denk [Sat, 15 Oct 2005 16:43:50 +0000 (18:43 +0200)]
Add missing CHANGELOG entry.

12 years agoMerge with /home/m8/git/u-boot
Wolfgang Denk [Sat, 15 Oct 2005 16:23:43 +0000 (18:23 +0200)]
Merge with /home/m8/git/u-boot

12 years agoAdd fat & ext2 support to AMCC 440EP boards Yosemite & Bamboo
Stefan Roese [Fri, 14 Oct 2005 13:37:34 +0000 (15:37 +0200)]
Add fat & ext2 support to AMCC 440EP boards Yosemite & Bamboo
Patch by Stefan Roese, 14 Oct 2005

12 years agoFix identification on ext2ls help entry
Stefan Roese [Fri, 14 Oct 2005 13:34:07 +0000 (15:34 +0200)]
Fix identification on ext2ls help entry
Patch by Stefan Roese, 14 Oct 2005

12 years agoCleanup for GCC-4.x
Wolfgang Denk [Thu, 13 Oct 2005 14:45:02 +0000 (16:45 +0200)]
Cleanup for GCC-4.x